South Africa is in a water crisis and wastewater reuse, desalination and potable water quality are top of the agenda. Where will our future water be sourced?
The most common solutions to South Africa’s water challenges usually entail a massive infrastructure capital spend and long-term implementation. The belief that scale always brings down the unit costs leads to focus on centralised water catchment and treatment – the bigger, the better, the cheapest and the easiest to operate. In looking towards megaprojects to solve the entire South African water crisis, we tend to forget about the smaller, easier projects that can assist with water supply. With failing infrastructure, which includes the pipelines transporting water for hundreds of kilometres across the country, decentralised water treatment starts making sense for smaller, remote communities or industry. Advanced technologies provide a smaller footprint, less operator involvement and less dependency on chemicals for water treatment. QFS has brought globally leading technologies to South Africa and localised them to be more affordable for South African applications.
Wastewater reuse
There are a number of small wastewater facilities of between 1 MLD and 5 MLD scattered throughout South Africa. Most of the water at these facilities is not seen as a source but as an environmental contamination risk. Rural wastewater facilities compete with many other services for the budgets of local authorities and are often neglected, suffering from insufficient maintenance and incorrect operation. The wastewater facilities are also under pressure to produce water good enough to release into a natural source. However, this ‘liability’ can be turned into an income stream, using the correct technology to produce safe irrigation or industrial water. For the reuse process to be successful, there has to be infrastructure in place to biologically treat the raw sewage. The biological process must be able to produce water of acceptable quality for the reuse process to accept this for further treatment.
The process
QFS offers modular, pre-designed systems that can be installed with minimal site work. The following core technologies for water treatment are available:
- Flocculation/clarifier
- Drum screen @ 20 micron
- Ultrafiltration (UF)
- Advanced oxidation
- Granular activated carbon
1 Flocculation/clarifier
A clarifier allows for flocculation to be included in the pre-treatment process. Chemical dosages will be confirmed during the final design phase, but typically three dosing stations are included for the addition of chlorine, pH correction and flocculants. The clarifier combats high solid carry-over from the treatment works and adds the ability for organic flocculation. Carry-over solids enter the clarifier and settle out with the assistance of installed tubular settlers, which utilise individual, isolated tubular channels. The modules are engineered with the individual tubes rising in the same direction to eliminate mixing currents and unstable flow patterns. Structural ribs provide considerable vertical loading structural strength. The unique design insures a solid interface during installation. Grating panels are installed on top of the tube settler packs to provide UV protection against extended exposure to sunlight. The grid also replaces a possible mobile walkway, as well as providing a protective layer from foot traffic and the repeated hydraulic impact of routine wash-downs.
2 Drum screen @ 20 micron
Clarified water will overflow to the drum screen in a concrete channel. The drum screen filters from the inside of the drum to the outside using gravity pressure. Screened water will fall into the UF buffer tank. The drum is fully automated and automatically cleaned with a set of nozzles, and cleaning commences as soon as the drum starts turning.
3 Ultrafiltration
UF is seen to be a core technology in the reuse process. The fixed removal rating of the UF membrane ensures the removal of pathogenic organisms, even those that are chlorine resistant. Each UF membrane filtration module comprises of a bundled group of hollow fibre membranes, surrounded by a protective plastic screen and sealed with polyurethane ‘pots’ at both ends. The pots allow filtered water to pass from the hollow inner core, or lumen, of the membrane fibres to the filtrate pipe sets. QFS’s Memcor L20 module housing acts as a pressure vessel for each membrane filtration module. Each L20 module house has two headpieces, two outer sleeves and a centre tube. Valves in the headpieces isolate both the inlet feeds and the filtrate outlets. In filtration, feedwater enters the module array through the feed ports in the end pipe sets, passes into the filtration modules, and through the membranes. Filtrate exits the module array through the filtrate ports and pipework flowing to the filtrate storage tank or service discharge point.
4 Advanced oxidation
The advanced oxidation process of ultraviolet radiation in combination with hydrogen peroxide (UV/H2O2) is well understood and documented. The H2O2 is dosed after the carbon filters and before the UV light.
5 Granular activated carbon
The granular activated carbon media filter consists of modified steel pressure vessels. Water will enter the vessel from the top and exit at the bottom. Backwash will be performed by a flow reversal and four filtration flow rates used for proper fluidisation of the media bed. The granular activated carbon is made of selected virgin coal, produced under high-pressure extruding and strictly controlled steam activation processes at a high temperature. This granular activated carbon is characterised by a large surface area, uniform pore structure, high hardness, enhanced filtration and regeneration ability.
Conclusion
Herman Smit, MD of QFS, believes the above system provides the best solution for decentralised water reuse projects to supply irrigation or industrial water from wastewater treatment works. “QFS has represented Evoqua (formerly Siemens Water Technologies) in South Africa for over 14 years, and has successfully implemented potable and wastewater projects. We are well positioned to provide equipment through our in-house manufacturing and implementation, and our personnel are familiar with all of the technologies required,” says Smit. “QFS is also available to work with the client should any changes be required during the final design stage of the project.”